Cel-Fi Go X Repeater Compact Trucker Kit 3G/4G

Product Description

Cel-Fi Go X G32 Smart Repeater Compact Trucker Kit 3G/4G is suitable for cars, trucks, utes, 4WD, RV, Motor Homes and other vehicle applications. Supports either Optus or Vodafone and can boost two frequencies allowing simultaneous 3G and 4G operation. Ideal for applications where a compact and rugged external antenna is required such as smaller cars and operating in high wind harsh environments. Includes a mini Stainless Spring Fibreglass Omni Directional Antenna and Coverage Panel Antenna.Supports either Optus or Vodafone. For low loss extension cables and antenna mounting brackets, see ACCESSORIES below.

Downloads
	Cel-Fi GO X G32 Optus/Vodafone Data Sheet

Learn how to choose the right antenna for your Vehicle or 4WD

Cel-Fi Go X G32 Smart Repeater is based on the Nextivity's Cel-Fi GO Mobile Phone Repeater and has been tested, authorised and approved by Optus and Vodafone for use on their networks.

Cel-Fi Go X G32 Smart Repeater will boost 3G and 4G on either the Optus or Vodafone (selectable) Australian cellular network and is is designed to dramatically boost voice quality and increase data speeds for in vehicle, 4WD and building applications. Note that the Cel-Fi Go X when configured for Vodafone will not boost the Vodafone Regional network. You can tell you’re using the Regional Network when ‘Vodafone AU R’ or ‘Voda R’ appears on your phone. This is due to the Regional Network roaming on a partners network. More information can be found on Vodafone’s Regional Network page.

When configured for Optus, the Cel-Fi Go X G32 Smart Repeater operates on 3G 900Mhz or 4G 1800/2600MHz bands and supports two (2) bands simultaneously.

When configured for Vodafone, the Cel-Fi Go X G32 Smart Repeater operates on 3G 900Mhz and 4G 1800/2100MHz bands and supports two (2) bands simultaneously.

Cel-Fi Go X Smart Repeater offers a more flexible installation over other Cel-Fi models due to the ability to run cables to where the signal is needed most. By not having a wireless link between two boxes GO can operate in areas that are saturated with Wi-Fi.

• For building and vehicle applications
• Locked to Optus or Vodafone Mobile Network
• Carrier approved
• Bluetooth WAVE App for iPhone, Android & Computers

Supported Networks when configured for Optus - Optus, Amaysim, Dodo, iiNet, plus more*.

Supported Networks when configured for Vodafone - Vodafone Australia, Redbull Mobile, plus more*.

*Note: Some supported networks are not fully featured.

Includes:

• Cel-Fi Go X G32 Smart Repeater
• 5dBi Compact (40cm) Stainless Spring Fibreglass OMNI External Antenna with 4m LMR195 grade low loss cable
• Adhesive backed Internal Panel Antenna with 3m RG174U grade cable
• 12V cigarette lighter plug (CLA)

Installation should be carried out strictly in accordance with the Cel-Fi GO Quick Start Guide and any other information contained in the box. Vehicle installations of the Cel-Fi Go Mobile in particular requires special attention not to interfere with air bag mechanisms, safety and control systems, ABS, stability and traction systems and the vehicles auto electrics in general. You should be familiar with applicable federal and state regulations and industry standards regarding installation. Incorrect installation may result in water leaks, electrical damage, fusing and risk of fire. Misuse of this equipment or failure to follow the instructions in the Quick Start Guide could result in injury and equipment damage. In no event will Comnet Solutions be responsible or liable for either indirect or consequential damage or injury that may result from the installation or use of this equipment. Please contact our Support Team if you have any questions regarding the above precautions. Use our online Contact Form for quick response.

Specifications are subject to change without notice. Picture may not be exact model as described.

ACCESSORIES

2m Antenna Cable LMR195 SMA Male to SMA Female		5m Antenna Cable LMR195 SMA Male to SMA Female		Antenna Mounts		Cel-Fi Go Vehicle Basic Installation